Archives: Products
Showing 9681–9696 of 23773 results
-
3616 SHIMRp296.000Read moreIndexa Indexable Tooling Spares – Shims
Within the Index-Seiki range of indexable tooling spares you will find insert screws, Torx keys, shims, clamps and pins to fit the Index-Seiki toolholder you are using.
-
36mm CARBIDE TIPPED HOLESAWRead moreCarbide Tipped Holesaws
Kennedy® carbide tipped hole saws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel. Use standard arbors.
-
36mm CHROME VANADIUM COMBINATION SPANNERRead moreKennedy Industrial Combination Spanners – Metric
Metric
Manufactured from chrome vanadium steel with a satin finish body and highly polished heads. 15 open jaw angle to shank and ring end offset.
Conform to:
5.5mm – 25mm, 1/4″ – 1″ AF – DIN 3113.
26mm – 50mm, 11/16″ – 2″AF – ASME B107.6.
1/8″ – 1/2″ Whitworth – DIN 3113 & BS192:1982.
9/16″ – 7/8″ Whitworth – ASME B107.6 & BS192:1982. -
36mm DEEP IMPACT SOCKET 1″ SQ DRRead moreKennedy Chrome Molybdenum Impact Sockets: 1″ Drive Metric, Deep Length, 6-Point
1â Drive Metric, Deep Length, 6-Point
Conform to: DIN 3129.Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.
-
36mm DEEP IMPACT SOCKET 3/4″ SQ DRRead moreChrome Molybdenum Impact Sockets: 3/4″ Drive Metric, Deep Length, 6-Point
3/4″ Drive Metric, Deep Length, 6-Point
Conform to: DIN 3129.Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.
-
36mm IMPACT SOCKET 1-1/2″ DRRead moreChrome Molybdenum Impact Sockets: 1 1/2″ Drive Metric Size, Standard Length, 6-Point
1 1/2″ Drive Metric Size, Standard Length, 6-Point
Conform to: SAE, USA Federal Standard GGG-W-660A.Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.
-
36mm IMPACT SOCKET 1″ SQDRRead moreKennedy Chrome Molybdenum Impact Sockets: 1″ Drive Metric, Standard Length, 6-Point
Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.
-
36mm IMPACT SOCKET 1/2″ SQ DRRead moreKennedy Chrome Molybdenum Impact Sockets: 1/2″ Drive Metric, Standard Length, 6-Point
1/2″ Drive Metric, Standard Length, 6-Point
Conform to: DIN 3129.Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.
-
36mm IMPACT SOCKET 3/4″ SQ DRRead moreChrome Molybdenum Impact Sockets: 3/4″ Drive Metric, Standard Length, 6-Point
3/4″ Drive Metric, Standard Length, 6-Point
Conform to: DIN 3129.Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.
-
36mm LONG MULTI-TOOTH CUTTERRead moreM2 Multi-Tooth Milling Cutters
Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.
Sizes available: 2 – 52mm diameter short and 13 – 52mm diameter long series.Long Series
Shank diameter: 19mm/3/4â.
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm. -
36mm O/E PODGER SPANNERRead moreKennedy Open End Podger Spanners
Designed to engage the nut from the side. As it only engages on two faces of the fastener, care must be taken to ensure that the correct size spanner is always used. Tapered handle for assisting with alignment of fixing holes on jigs and fabrications.
-
36mm OPEN JAW SLOGGING WRENCHRead moreKennedy Open Jaw Slogging Spanners
Forged and hardened steel. Flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. To DIN 133.
-
36mm RING CRANKED PODGERSPANNERRead moreKennedy Ring End Podger Spanners
Cranked handle assists with location of spanner on to fixings within a recess.
-
36mm RING SLOGGING WRENCHRead moreRing Slogging Spanners
Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. Manufactured to DIN 7444.
-
36mm SHORT MULTI-TOOTH CUTTERRead moreM2 Multi-Tooth Milling Cutters
Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.
Sizes available: 2 – 52mm diameter short and 13 – 52mm diameter long series.Short Series
Shank diameter: 19mm/3/4â.
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm. -
36mm SINGLE HEX SOCKET 1/2″ SQ DRRead moreKennedy Single-Hexagon Standard Length Sockets, 1/2″
Single-Hexagon Sockets
Six point – offer a more positive location, particularly on worn or rounded nuts, but require a one-sixth turn to engage the next point of the socket.