Category: HSS Taper Pin Reamers

HSS Taper Pin Reamers

Showing all 14 results

  • 1.50mm HSS S/S ST/FL HAND TAPER PIN REAMER

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 10.00mm HSS S/S ST/FL HAND TAPER PIN REAMER
    Rp1.451.000

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 12.00mm HSS S/S ST/FL HAND TAPER PIN REAMER
    Rp1.670.000

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 13.00mm HSS S/S ST/FL HAND TAPER PIN REAMER

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 14.00mm HSS S/S ST/FL HAND TAPER PIN REAMER

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 16.00mm HSS S/S ST/FL HAND TAPER PIN REAMER

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 2.00mm HSS S/S ST/FL HAND TAPER PIN REAMER

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 2.50mm HSS S/S ST/FL HAND TAPER PIN REAMER

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 20.00mm HSS S/S ST/FL HAND TAPER PIN REAMER

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 3.00mm HSS S/S ST/FL HAND TAPER PIN REAMER
    Rp581.000

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
  • 4.00mm HSS S/S ST/FL HAND TAPER PIN REAMER
    Rp647.000

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Add to cart
  • 5.00mm HSS S/S ST/FL HAND TAPER PIN REAMER
    Rp698.000

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Add to cart
  • 6.00mm HSS S/S ST/FL HAND TAPER PIN REAMER
    Rp814.000

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Add to cart
  • 8.00mm HSS S/S ST/FL HAND TAPER PIN REAMER
    Rp1.028.000

    HSS Straight Shank Hand Taper Pin Reamers

    Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

    Metric Tolerances
    Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
    Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000.

    Read more
0
    0
    Your Cart
    Your cart is emptyReturn to Shop