Showing all 16 results

• 

  32mm VISCOUS HUB SPANNER

  Kennedy Viscous Hub Spanners

  For the removal of thermal viscous fan hubs. Suitable for most makes of car.

  Read more
• 

  36mm VISCOUS HUB SPANNER

  Kennedy Viscous Hub Spanners

  For the removal of thermal viscous fan hubs. Suitable for most makes of car.

  Read more
• 

  ANTI-FREEZE TESTER

  Kennedy Anti-Freeze Tester

  Suitable for use with Ethylene Glycol or Methanol type anti-freezes. Shows lowest temperature at which the cooling system is protected against freezing. Tough glass tube construction with an easy to read scale. For use on hot or cold engines.

  Read more
• 

  BALL JOINT SERVICE TOOL SET WITH 4X4 ADAPTOR

  Kennedy Ball Joint Servicing Kit

  Made from cast iron and hardened carbon steel, this kit is designed for the removal of press fit type ball joints without having to remove the control arm from the vehicle. The kit can also be used for removing brake anchor pins and the servicing of universal joint bearings.
  Set Includes all the receive tubes and removing/installing adapters needed for press fit parts such as ball joints, universal joints and truck brake anchor pins.

  This tool kit is designed for servicing universal joints on all cars and light trucks that have press-fit type ball jointswithout the need to remove the control arm from the vehicle

  Contents:
  1 x C-frame press and Forcing Screw.
  3 x Receiver tubes: 2-3/4″ x 3″ / 2-1/4″ x 2-1/2″ / 1-3/4″ x 2″
  Installation/Removal Adaptor & Cups
  4-wheel drive ball joint service kit for 1967-present 1/2 & 3/4 ton vehicles with Dana 44 front axle, (eg: Ford, GM, Dodge, IHC & Jeep).

  Read more
• 

  DOUGHNUT STRETCHER

  Kennedy Exhaust Doughnut Puller

  To enable fast Installation or removal of rubber anti-vibration mounting rings found on modern exhaust systems. Puller has offset hook for easier application and dipped vinyl handle for added comfort and extra grip. Manufactured from hardened steel. Length: 290mm

  Read more
• 

  LONG HANDLED GASKET SCRAPER SET (3-PCE)

  Kennedy Gasket Scraper Set

  Long Handled Gasket Scraper Set
  For cleaning cylinder heads and removing old sealants and carbon build up. Hardened and tempered carbon steel shanks and heads are ‘offset to edge’ to allow easy scraping of flat surfaces. Simple ‘firmer’ style bevelled points with longer head lengths allow for scrapers to be re-ground several times for maximum service life. Impact resistant square section handle for secure grip even when greasy.
  Set includes blade widths: 19mm (3/4”), 25mm (1”) and 38mm (1 1/2”).
  Overall length: 280mm (11”).

  Read more
• 

  MAGNETIC WING COVER 1100mmx400mm

  Kennedy Magnetic Wing Cover

  Designed to be used in the workshop to protect car wings when working. Manufactured from heavy duty vinyl with a soft backing to prevent any scratching or marking of paintwork when in use. The cover is held in place by magnets stitched into the material. Folds to a quarter of its length for storing.

  Read more
• 

  MECHANICS STETHOSCOPE

  Kennedy Mechanic’s Stethoscope

  Professional stethoscope provides a fast and easy way to locate noises in engines or bearings and other moving parts. High quality surgical grade PVC and rubber parts for increased sound definition, plastic ear-pieces minimise outside noise with an
  aluminium alloy probe/needle for finding the exact location of specific noises.
  Supplied with rubber trumpet for checking vacuum and pressure flow. Useful for synchronising multi carburettors, helps to track dashboard rattles and is ideal for pinpointing unusual vibrations or suspected leaks, it is also shockproof.

  Add to cart
• 

  MULTI-PURPOSE SCRAPER SET (4-PCE)

  Kennedy Standard Length Gasket Scraper Set

  Rigid carbon scrapers ideal for cleaning cylinder heads, removing old sealants, carbon build up and a variety of general mutipurpose automotive applications.
  Set includes blade lengths: 205 x 13mm (8” x 1/2”), 205 x 25mm (8” x 1”), 93 x 25mm (31/2” x 1”), 97 x 15mm (33/4” x 5/8”).

  Read more
• 

  NOID LIGHT SET 6-PCE

  Kennedy Noid Light 6 Piece Test Set

  NLT060
  The Kennedy® Noid light test set is for diagnosing fuel injector signal faults fast. Simply disconnect the injector harness and plug in the relevant noid light. Turn the ignition on – if the light is constant or absent, then the signal from the ignition system is at fault.
  Easy to use and fits a wide variety of injector harnesses.
  Compatible with: GM – TBI GM – SCPI. GM – PFI
  FORD – TBI GEO – TBI BOSCH – PFI

  Read more
• 

  OIL DRAIN PLUG KEY SET 3/8″ SQ. DR. (17-PCE)

  Kennedy Oil Drain Plug Key Set

  DPK017
  A comprehensive set of quality 3/8” sq. drive oil drain plug keys with tommy bar.
  Made from satin finished chrome vanadium.
  Contents: Male Square: 7mm, 8mm (5/16”), 9mm, (3/8”), 10mm, 11mm, 12mm and 13mm. Female Square: 10mm.
  Male Hex: 8, 9, 10, 12, 14 and 17mm. Male Triangular 10mm. Tommy bar.

  Read more
• 

  OXYGEN SENSOR SOCKET

  Kennedy Oxygen Sensor Socket

  1/2” square drive. 22mm hex. x 90mm length. Cutaway section allows socket to pass overwiring.

  Read more
• 

  OXYGEN SENSOR SOCKET SET 3-PCE

  Kennedy Oxygen, “EGO”, “O2”, “Lambda” Sensor Socket set

  Three piece universal set. Essential for servicing today’s computer-controlled vehicle systems. Easily removes exhaust gas oxygen sensors (known as ‘EGO’, ‘O2’ or ‘Lambda’ sensors), vacuum switches and pressur, Vauxhe switches. Also suitable for diesel injectors found on Mitsubishi, Nissan, Opelall and VW vehicles. Made from heat treated cast steel.

  Set contains:
  22mm (7/8”) hex, 1/2” square drive socket with 7.5mm side slot for sensor wire clearance. Socket has 22mm hex for use with a spanner. Overall length: 80mm.
  22mm (7/8”) hex, crow’s foot style wrench, 1/2” square drive (double square for easy access). With full length 11mm slot for total clearance of switch/sensor wire
  22mm (7/8”) hex, crow’s foot style wrench, 3/8” square drive. With full length 8.6mm slot for total clearance of switch/sensor wire.

  Read more
• 

  REMOTE HOSE CLAMP PLIERS

  Kennedy Remote Hose Clamp Pliers

  Kennedy Remote Hose Clamp Pliers are for the removal and replacement of fuel, oil and water hoses, suitable for working in confined engine compartments.

  Flexible 530mm long reach ratchet mechanism allows the pliers to release and lock hose clamps in the opened position.

  Supplied complete with a cable clamping nipple for use when replacing the cable.

  Capacity: 55mm.

  Read more
• 

  SEAL PULLER TOOL

  Kennedy Seal Puller Tool

  Two size tips allow you to remove oil or grease seals from virtually anything including wheel bearings, transmission housings, etc. Hardened and tempered carbon steel shank and head with oxidised finish tips, chrome plated shank for protection against corrosion. Impact resistant square section handle for secure grip even when greasy.
  Overall length: 310mm (12 1/4”).

  Read more
• 

  VACUUM TESTING & BRAKE BLEEDING KIT

  Kennedy Vacuum Testing & Brake Bleeding Kit

  Vacuum testing kit that helps to locate and identify faults on cars, motorcycles and commercial vehicles. Supplied in robust blow moulded case.
  Contents: serviceable metal bodied vacuum pump, reservoir jar, transfer lid, storage lid, 4x lengths of 6mm ID tubing, 1x length of 4mm ID tubing adaptor. Set of brake bleeding adaptors, rubber cup adaptor.
  Maximum vacuum: 550mm Hg.
  Reservoir capacity: 150ml.

  Read more