Archives: Products
Showing 9617–9632 of 23773 results
-
35-50mm DIAL BORE GAUGERead moreOxford Dial Indicating Bore Gauges
29mm 1 1/8â Dial Diameter
Suitable for rapid, accurate measurement of size, concentricity, wear, taper, etc., in a wide range of bores. For workshop and inspection use. All models have one fixed and one moving anvil and a self-adjusting centre shoe. A âdatum pointâ can be set by using a setting ring of a known diameter or a micrometer. â Zeroâ the gauge to this datum point by rotating the bezel to align âzeroâ with the indicator. To check a bore is within tolerance, the limit hands can be fixed as required. All anvils are spring loaded to expand into the bore. For accurate reading ensure the stem of the gauge is parallel to the axis of the bore. This can be checked by ârockingâ the gauge back and forth until the smallest diameter is found. All models have inter-changeable anvils to cover a range of bore sizes.
Supplied in a tough hard case.Type – Metric
Graduation: 0.01mm
Face Dial: 57mm
Reading: 0-100
Travel Per Rev: 1mm
Total Travel: 3mmType – Inch
Graduation: 0.0005″
Face Dial: 2 3/16″
Reading: 0-25-0
Travel Per Rev: 0.050″
Total Travel: 0.25″ -
35.00mm HSS T/S DRILLRp2.020.000Read moreSherwood HSS Taper Shank Drills, 4 Morse Taper – Metric
Series T100
General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345. -
35.00mm HSS T/S SP/FL MACHINE REAMERRp5.031.000Read moreTaper Shank Machine Reamers
Used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head. Manufactured to BS 328-4.
Tolerances (to H7)
Diameter: ~ up to 3.00. Tolerance: +0.008, -0.007.
Diameter: Over 3.00 ~ up to 6.00. Tolerance: +0.010, -0.005.
Diameter: Over 6.00 ~ up to 10.00. Tolerance: +0.012, -0.006.
Diameter: Over 10.00 ~ up to 18.00. Tolerance: +0.015, -0.008.
Diameter: Over 18.00 ~ up to 30.00. Tolerance: +0.017, -0.009.
Diameter: Over 30.00 ~ up to 50.00. Tolerance: +0.021, -0.012.
Diameter: Over 50.00 ~ up to 80.00. Tolerance: +0.025, -0.014.
Diameter: Over 80.00 ~ up to 120.00. Tolerance: +0.029, -0.016. -
35.00mm x 530mm O/A HSS TAPER SHANK DRILLRead moreHSS Extra Length Taper Shank Drills to BS328 : 1 1986 – 3 Morse Taper, Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite.
Point angle 118°, helix angle: normal, web thickness: standard, relief angle 8° – 20°, tolerance of diameter: h8.
Made to BS328 : 1 1986. Sizes 32mm to 50mm are made to DIN1870/Series 1. -
35.0mm DIA DEEP POT MAGNETRead moreKennedy Deep Pot Magnets
North polarity in centre separated from opposing pole by a continuous slot. Ideally suited for gripping applications. Supplied with M5 x 1 threaded bore fixing hole and keeper.
*M3 x 0.5 -
35.50mm HSS T/S DRILLRead more
Sherwood HSS Taper Shank Drills, 4 Morse Taper – Metric
Series T100
General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345. -
35/64″ HSS S/S BRIGHT JOBBER DRILLRead moreHSS Jobber Drills Metric, Bright Finish – Inch
Series J100 – Inch
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10°-20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328/DIN338RN.Bright Finish
Drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials. -
35/64″ HSS S/S JOBBER DRILLRead moreHSS Jobber Drills Steam Tempered – Inch
Series J100
Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS 328/DIN338RN.Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining. -
35/64″ HSS T/S DRILLRead more
General Purpose HSS Taper Shank Drills, 1 Morse Taper – Inch Sizes
Suitable for single and multi-spindle drilling machines. The taper shank being the engineering industries recognised standard and most widely used method for holding and driving cutting tools. Manufactured to BS 328 : Part 1 : 1986, DIN 345RN, DIN 343RN.
-
350cc METAL OIL CAN – FORCE FEED PUMPRead moreKennedy Metal Oil Cans
Enamel finish, heavy gauge, seamless metal- bodied oil cans. With positive force feed brass pumps and valves. Supplied with both rigid metal and flexible nylon threaded
spouts. -
350cc PLASTIC OIL CAN 6″NYLON SPOUTRead moreKennedy Plastic Oil Cans
One-piece moulded plastic bodies with positive force feed pumps, supplied with nylon push-fit spouts.
*150mm spouts
**230mm spouts -
350ml SNAP-BOTTOM OIL CANRead moreKennedy âSnapâ Bottom Oil Can
350ml traditional âstyleâ seamless metal oil can with enamel finish. Invert can and pop the bottom for an exact application. Supplied with 120mm rigid metal spout.
-
350mm CRANKED BANDS & HOOKS ON PLATE BLACK (PR)Read moreCRANKED BANDS & HOOKS ON PLATE
Supplied packed in pairs in a polythene bag and complete with all fixing screws and bolts. Supplied individually, boxed in 5’s.
-
350mm CRANKED BANDS & HOOKS ON PLATE GALV. (PR)Read moreCRANKED BANDS & HOOKS ON PLATE
Supplied packed in pairs in a polythene bag and complete with all fixing screws and bolts. Supplied individually, boxed in 5’s.
-
350mm DOUBLE GATE FASTENER SET C/W FITTINGS GALV.Read moreDouble Gate Fastener Set
Each set consists of 460mm galvanised garage door drop bolt, BZP tubular receiver with square plate receiver, 350mm galvanised medium throw-over loop and all fixings to suit 75mm (3″) thick gates. Supplied individually, boxed in 5’s.
-
350mm MEDIUM TEE HINGES BLACK (PR)Read moreTee Hinges (Supplied as pairs)
Suitable for medium load applications such as stable doors. Material thickness up to 2.6mm.