Archives: Products
Showing 5793–5808 of 23773 results
-
19.00mm HSS 1/2″ PARALLEL SHANK DRILLRp360.000Read moreHSS Reduced Shank Drills (Blacksmiths)
1/2â parallel shank. General purpose drills for light duty work, for drilling steels, cast iron, nickel brass and graphite. Reduced parallel shank 1/2â. Point angle: 118°, helix angle: normal, web thickness: standard, tolerance of diameter: h8, tolerance of shank: 0.01/0.08. Manufactured to works standard.
-
19.00mm HSS S/S BRIGHT JOBBER DRILLRp409.000Read moreSherwood HSS Jobber Drills Metric, Bright Finish – Metric
Series J100 – Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10°-20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328/DIN338RN.Bright Finish
Drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials. -
19.00mm HSS S/S JOBBER DRILLRp465.000Read moreSherwood HSS Jobber Drills Steam Tempered – Metric
Series J100 – Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328/DIN338RN.Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining. -
19.00mm HSS S/S STUB DRILLRead moreSherwood HSS General Purpose Stub Drills – Metric Sizes
Series S100 – Metric
General purpose drills for use on automatics and turret lathes. Suitable for drilling steels, cast iron, alloy steel and malleable cast iron. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BSâ328: Part 1: 1986/DIN 1897. -
19.00mm HSS SP/FL PARALLEL HAND REAMERRp1.239.000Read moreStraight Shank Parallel Hand Reamers
Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.
Metric Tolerances
Diameter: ~ up to 3.00. Tolerance: +0.008, -0.007.
Diameter: Over 3.00 ~ up to 6.00. Tolerance: +0.010, -0.005.
Diameter: Over 6.00 ~ up to 10.00. Tolerance: +0.012, -0.006.
Diameter: Over 10.00 ~ up to 18.00. Tolerance: +0.015, -0.008.
Diameter: Over 18.00 ~ up to 30.00. Tolerance: +0.017, -0.009.
Diameter: Over 30.00 ~ up to 50.00. Tolerance: +0.021, -0.012. -
19.00mm HSS T/S DRILLRp486.000Read moreHSS Taper Shank Drills – Metric Continued
To drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8.
Manufacturing Standard: DIN 345. -
19.00mm HSS T/S SP/FL MACHINE REAMERRp1.413.000Read moreTaper Shank Machine Reamers
Used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head. Manufactured to BS 328-4.
Tolerances (to H7)
Diameter: ~ up to 3.00. Tolerance: +0.008, -0.007.
Diameter: Over 3.00 ~ up to 6.00. Tolerance: +0.010, -0.005.
Diameter: Over 6.00 ~ up to 10.00. Tolerance: +0.012, -0.006.
Diameter: Over 10.00 ~ up to 18.00. Tolerance: +0.015, -0.008.
Diameter: Over 18.00 ~ up to 30.00. Tolerance: +0.017, -0.009.
Diameter: Over 30.00 ~ up to 50.00. Tolerance: +0.021, -0.012.
Diameter: Over 50.00 ~ up to 80.00. Tolerance: +0.025, -0.014.
Diameter: Over 80.00 ~ up to 120.00. Tolerance: +0.029, -0.016. -
19.00mm HSS-COBALT T/S DRILLRp742.000Read moreHSS-Co 5% Taper Shank Drills
High heat resistant drill for drilling alloyed and unalloyed steels and castings with a tensile strength over 800N/mm2. Especially suitable for hot and cold rolled steels as well as case hardening and heat treatable steels. Manufactured to Type N DIN 345.345.
-
19.00mm x 315mm O/A HSS TAPER SHANK DRILLRead moreHSS Extra Length Taper Shank Drills to BS328 : 1 1986 – 2 Morse Taper, Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite. Point angle 118°, helix angle: normal, web thickness: standard, relief angle 8° – 20°, tolerance of diameter: h8. Made to BS328 : 1 1986. Sizes 32mm to 50mm are made to DIN1870/Series 1
-
19.00mm x 400mm O/A HSS TAPER SHANK DRILLRead more
HSS Extra Length Taper Shank Drills to BS328 : 1 1986 – 2 Morse Taper, Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite. Point angle 118°, helix angle: normal, web thickness: standard, relief angle 8° – 20°, tolerance of diameter: h8. Made to BS328 : 1 1986. Sizes 32mm to 50mm are made to DIN1870/Series 1
-
19.0mm HEXAGON WRENCHRead moreKennedy Hexagon Key L-Wrenches: Metric – Standard Length
Metric – Standard Length
Manufactured from fully hardened carbon steel in accordance with DIN 911 ensuring a quality ductile key with precision square cut ends and accurate AF dimensions to ensure full socket contact. Black finish. -
19.0mm LONG ARM HEXAGON WRENCHRead moreKennedy Hexagon Key L-Wrenches, Long Arm – Metric
Metric – Long Arm
Manufactured from fully hardened carbon steel in accordance with DIN 911 ensuring a quality ductile key with precision square cut ends and accurate AF dimensions to ensure full socket contact. Black finish. -
19.0×12.7mm 9.5RAD 1/4″SK. 2FL CORE BITRead moreRouter Cutters
Two Flute Core Box Bits
Cutters suitable for edge moulding, face grooving and fluting on components such as desk tops, draining boards and panels. -
19.0×12.7mm CUT 1/4″SHK.2FL PLUNGE BITRead moreRouter Cutters
Two Flute Classical Plunging Bits
Rough bottom. Used to produce flat bottom panel mould on cabinet and drawer fronts. Can also be used for edge mouldings. -
19.0×14.5mm 6.3RAD 1/4″SK 2FL R/OVER BITRead moreRouter Cutters
Two Flute Rounding Over Bits
For panel and edge moulding work, such as table tops and window boards. For use with template guide. -
19.0x19mm CUT 1/4″SHK. 2FL MORTISING BITRead moreRouter Cutters
Two Flute Hinge Mortising Bits
Designed with large chip clearance at base. Suitable for hinge recessing and shallow flat bottom apertures.