Archives: Products
Showing 2449–2464 of 23773 results
-
100x34mm T/P SWIV’ CASTOR ZINC)NYLON WHEEL & BRAKERead moreNylon Wheel Swivel Type with Plain Bore – Zinc Finish
Suitable for use on compact floors (cement, tiles, etc). Particularly recommended for the food processing industry. Not recommended for use where mineral or organic acids are present. Operating temperature range -10C to 60C.
-
100x3x16mm A24RBF DPC CUTTING DISCRead moreType 42 Depressed Centre Cutting
Type 42 Depressed Centre Cutting
For use with all portable grinders/cut-off machines. Not to be used for âfree handâ cutting and importantly not to be used for grinding.
Grade A24/A46 – For general purpose cutting on metals.Depressed Centre & Flat Reinforced Cutting & Grinding Discs
All Kennedy Depressed Centre and Flat Reinforced Cutting Wheels now carry the âoSaâ (The Organisation for the Safety of Abrasives) mark of approval. âoSaâ is an association of the worldâs leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels.
Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. âoSaâ marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA. -
100x3x16mm A24RBF FLAT CUTTING DISCRead moreType 41 Flat Reinforced Cutting
Type 41 Flat Reinforced Cutting
For use with all portable angle grinders. 180mm to 230mm discs can also be used on circular saws, and 300 to 350mm discs are for use with chop saws/cut-off machines, subject to bore compatibility. Not to be used for wet cutting.
Grade A24/A36 – For general-purpose cutting on metals.
Grade C24 – For general-purpose cutting on stone.Depressed Centre & Flat Reinforced Cutting & Grinding Discs
All Kennedy Depressed Centre and Flat Reinforced Cutting Wheels now carry the âoSaâ (The Organisation for the Safety of Abrasives) mark of approval. âoSaâ is an association of the worldâs leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels.
Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. âoSaâ marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA. -
100x3x16mm C24RBF FLAT STONE CUTTING DISCRead moreType 41 Flat Reinforced Cutting
Type 41 Flat Reinforced Cutting
For use with all portable angle grinders. 180mm to 230mm discs can also be used on circular saws, and 300 to 350mm discs are for use with chop saws/cut-off machines, subject to bore compatibility. Not to be used for wet cutting.
Grade A24/A36 – For general-purpose cutting on metals.
Grade C24 – For general-purpose cutting on stone.Depressed Centre & Flat Reinforced Cutting & Grinding Discs
All Kennedy Depressed Centre and Flat Reinforced Cutting Wheels now carry the âoSaâ (The Organisation for the Safety of Abrasives) mark of approval. âoSaâ is an association of the worldâs leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels.
Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. âoSaâ marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA. -
100×4.00mm (5/32″) PARALLEL PIN PUNCHRead moreKennedy Parallel Pin Punches
Ideal for driving tight fitting pins out of mechanical assemblies or realigning holes to fit dowel pins. Manufactured from hardened and tempered steel. With a knurled body for extra grip. Conform to BS 3066.
-
100×4.00mm (5/32″) SQUARE HEAD CENTRE PUNCHRead moreKennedy Square Head Centre Punches
Non-roll. Manufactured from hardened and tempered steel with a knurled body for positive grip. Precision ground 60° point for accurate marking of workpiece.
Conform to BS 3066.*Round headed.
-
100×4.00mm (5/32″) SQUARE HEAD NAIL PUNCHRp73.000Add to cartKennedy Nail Punches
Cupped and bevelled precision ground points provide accurate positioning over the nail head for efficient depression. Manufactured from hardened and tempered steel, with a knurled body for extra grip.
Conform to BS 3066. (Hardness: heads 42 HRC. Max: points 52 – 58 HRC).
Overall length: 100mm (4â). -
100×4.80mm (3/16″) PARALLEL PIN PUNCHRp47.000Add to cart
Kennedy Parallel Pin Punches
Ideal for driving tight fitting pins out of mechanical assemblies or realigning holes to fit dowel pins. Manufactured from hardened and tempered steel. With a knurled body for extra grip. Conform to BS 3066.
-
100×4.80mm (3/16″) SQUARE HEAD CENTRE PUNCHRp71.000Add to cart
Kennedy Square Head Centre Punches
Non-roll. Manufactured from hardened and tempered steel with a knurled body for positive grip. Precision ground 60° point for accurate marking of workpiece.
Conform to BS 3066.*Round headed.
-
100x40mm AL/OX SANDING BANDS GRIT 150Read moreYork Sanding Bands
Spiral wound with tear-resistant backing fabric. For grinding and finishing edges, profiles, welded joints etc. For use with power tools. Aluminium Oxide for use on most metals.
* P60 = Coarse, P80 = Medium, P150 = Fine. -
100x40mm AL/OX SANDING BANDS GRIT 60Read moreYork Sanding Bands
Spiral wound with tear-resistant backing fabric. For grinding and finishing edges, profiles, welded joints etc. For use with power tools. Aluminium Oxide for use on most metals.
* P60 = Coarse, P80 = Medium, P150 = Fine. -
100x40mm AL/OX SANDING BANDS GRIT 80Read moreYork Sanding Bands
Spiral wound with tear-resistant backing fabric. For grinding and finishing edges, profiles, welded joints etc. For use with power tools. Aluminium Oxide for use on most metals.
* P60 = Coarse, P80 = Medium, P150 = Fine. -
100x40mm SPINDLE MOUNTEDHOLDERRead moreYork Drum Holders
Suitable for use with chucks/collets on all portable power and air tools. For use with spiral bound abrasive sanding bands. Self expanding when in use for a secure grip on the band. All shanks are 6mm except where marked * which has an 8mm shank.
-
100x40x65mm GRADE 2 VEE BLOCKS (PR)Read moreOxford Precision Vee Blocks
Matched and numbered pairs of closed grained iron castings accurately machined. Precision 90° vee blocks. Supplied as a pair.
-
100x4x16mm A30TBF DPC GRINDING DISCRead moreDepressed Centre & Flat Reinforced Cutting & Grinding Discs
Type 27 Depressed Centre Grinding
For use with all portable angle grinders. Not to be used for âfree handâ or wet grinding.
Optimum angle for use 25 to 35°.
Grade A30/AS30 – For general-purpose use on metals.
INOX – For use on stainless steel (iron, chlorine and sulphur free).Depressed Centre & Flat Reinforced Cutting & Grinding Discs
All Kennedy Depressed Centre and Flat Reinforced Cutting Wheels now carry the âoSaâ (The Organisation for the Safety of Abrasives) mark of approval. âoSaâ is an association of the worldâs leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels.
Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. âoSaâ marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA. -
100x50x6mm NYLON FINISHING WHEEL FINERead moreYork Shaft Mounted Combi Wheels – Finishing
Finishing Wheels
Made from high quality nylon, which is both flexible, durable and does not clog as easily as standard abrasive. 6mm shank diameter. Ideal for matching/blending a finish, light deburring, decorative/cosmetic applications. Alternate flaps of abrasive are interleaved with a versatile high quality nylon. 6mm shank diameter. Suitable for: deburring, producing cosmetic finishes on most materials, rust removal and blending.