Archives: Products
Showing 2497–2512 of 23773 results
-
102 P40 BRAZED TOOLRead moreKennedy Bar Turning Tools – P40
Brazed Tip Turning & Boring Tools
Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40: Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30: Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20: General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates. -
102mm CARBIDE TIPPED HOLESAWRead moreCarbide Tipped Holesaws
Kennedy® carbide tipped hole saws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel. Use standard arbors.
-
102mm DIA. (4″) BI-METALHOLESAWRp431.000Read moreConstant Pitch Bi-Metal HSS Holesaws
Featuring a constant pitch – first choice for cutting thin sheet materials up to 3mm thick. For producing high quality holes in wood, steel, brass, bronze, cast iron, aluminium and plastic. Featuring an hardened HSS cutting edge welded to a tough alloy steel body. Heavy duty shatter-resistant construction; virtually unbreakable. 6 teeth per inch.38mm (11/2â) cutting depth.
-
102mm DIA. (4″) BI-METALV/P HOLESAWRp431.000Read moreVariable Pitch Bi-Metal HSS Holesaws
For wood, steel, brass, bronze, cast iron, aluminium and plastic. Aggressive cutting action and M3 HSS cutting teeth to give a very smooth finish. Cuts up to 40% faster then constant pitch saws. The varying tooth pitch gives substantial reductions in noise by disrupting harmonics. Tooth life is greatly extended, as is battery life when used with a cordless drill. Suitable for all uses: engineering, construction and maintenance.4 to 6 teeth per inch.
28.5mm (11/8â) cutting depth. -
103 K20 BRAZED TOOLRead moreKennedy Bar Turning Tools – K20
Brazed Tip Turning & Boring Tools
Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40: Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30: Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20: General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates. -
103 P20/P30 BRAZED TOOLRead more
Kennedy Bar Turning Tools – P30
Brazed Tip Turning & Boring Tools
Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40: Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30: Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20: General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates. -
105mm BEARING SEPARATORRead moreKennedy Bearing Separators
For removing bearings, gears and bushes from shafts where access with a mechanical puller is restricted. Separators have tapered edge for insertion behind close fitting bearings, gears and bushes.
Jaw hardness: 42° – 45° HRC. -
105mm CARBIDE TIPPED HOLESAWRead moreCarbide Tipped Holesaws
Kennedy® carbide tipped hole saws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel. Use standard arbors.
-
105mm DIA. (4.1/8″) BI-METAL HOLESAWRp452.000Read moreConstant Pitch Bi-Metal HSS Holesaws
Featuring a constant pitch – first choice for cutting thin sheet materials up to 3mm thick. For producing high quality holes in wood, steel, brass, bronze, cast iron, aluminium and plastic. Featuring an hardened HSS cutting edge welded to a tough alloy steel body. Heavy duty shatter-resistant construction; virtually unbreakable. 6 teeth per inch.38mm (11/2â) cutting depth.
-
105mm DIA. (4.1/8″) BI-METAL V/P HOLESAWRp452.000Read moreVariable Pitch Bi-Metal HSS Holesaws
For wood, steel, brass, bronze, cast iron, aluminium and plastic. Aggressive cutting action and M3 HSS cutting teeth to give a very smooth finish. Cuts up to 40% faster then constant pitch saws. The varying tooth pitch gives substantial reductions in noise by disrupting harmonics. Tooth life is greatly extended, as is battery life when used with a cordless drill. Suitable for all uses: engineering, construction and maintenance.4 to 6 teeth per inch.
28.5mm (11/8â) cutting depth. -
105mm OPEN JAW SLOGGING WRENCHRead moreKennedy Open Jaw Slogging Spanners
Forged and hardened steel. Flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. To DIN 133.
-
105mm RING SLOGGING WRENCHRead moreRing Slogging Spanners
Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. Manufactured to DIN 7444.
-
106 P20/P30 BRAZED TOOLRead more
Kennedy Bar Turning Tools – P30
Brazed Tip Turning & Boring Tools
Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40: Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30: Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20: General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates. -
1080x457mm MOBILE LOUVRERACK DK GREY/LT GREYRead moreMatlock Mobile Trolleys/Racks
Similar to a free standing rack by mobile. Fitted with four 5â castors to the base which supports double sided louvre panels. Available in one height and two widths.
Colour: dark grey/light grey. -
1080x877mm MOBILE LOUVRERACK DK GREY/LT GREYRead moreMatlock Mobile Trolleys/Racks
Similar to a free standing rack by mobile. Fitted with four 5â castors to the base which supports double sided louvre panels. Available in one height and two widths.
Colour: dark grey/light grey. -
1086 CLAMP SCREWRp98.000Read moreIndexa Indexable Tooling Spares – Spare Parts
Within the Index-Seiki range of indexable tooling spares you will find insert screws, Torx keys, shims, clamps and pins to fit the Index-Seiki toolholder you’re using.