Archives: Products
Showing 15025–15040 of 23773 results
-
8mmx55mm HEX BIT SOCKET 1/2″ SQ. DR.Read moreYamoto Screwdriver Socket Bits, 1/2″
For insertion and removal of fasteners and fixings using 1/2â square drive tooling. Made from chrome vanadium steel, fully chrome plated with a mirror finish and aluminium-free to ensure non sparking. All have ball retaining groove on each face of the square drive. Conform to DIN standards.
-
8mmx69mm O/A HSS-COBALT 4FL PL/SH END MILLRp301.000Read moreHSS-Co Plain Shank Milling Cutters 4 Flute, Regular Length – Metric
Regular Length
Centre cutting, used for profile milling, milling keyways and producing open slots. Bright finish. Flute type: 30° Helix. Overall dimensions to DIN 844. Plain shank to DIN 1835A.Metric Tolerances
Nominal Dia.: Up to 38mm. Limits of Tolerance: +0.0630, -0.0130.
Nominal Dia.: Above 38mm. Limits of Tolerance: +0.1250, -0.0000. -
8mmx75mm HEXAGON BIT 10mm DRIVERead moreKennedy Screwdriver Bits: 10mm Hex Drive Bits – Hexagon
Hexagon
All Kennedy screwdriver bits have a hardness of 58 – 62HRC. High alloy chrome molybdenum steel for use on hand and power tools. -
8mmx75mm SPLINE BIT 10mm DRIVERead moreKennedy Screwdriver Bits: 10mm Hex Drive Bits – Spline
Spline
All Kennedy screwdriver bits have a hardness of 58 – 62HRC. High alloy chrome molybdenum steel for use on hand and power tools. -
8mmx88mm O/A HSS-COBALT 4FL PL/SH END MILLRp392.000Read moreSherwood HSS-Co Plain Shank Milling Cutters 4 Flute, Long Series – Metric
Long Series
Centre cutting, used for profile milling, milling keyways and producing open slots. Bright finish. Flute type: 30° Helix. Overall dimensions to DIN 844. Plain shank to DIN 1835A.Metric Tolerances
Nominal Dia.: Up to 38mm. Limits of Tolerance: +0.0630, -0.0130.
Nominal Dia.: Above 38mm. Limits of Tolerance: +0.1250, -0.0000. -
8mmx9mm CHROME VANADIUM O/E SPANNERRead moreYamoto Industrial Open Ended Spanners – Metric
Metric
Made from chrome vanadium steel with polished head and 15° offset. Conform to ASME B107.39. -
8mmx9mm DOUBLE ENDED BOXSPANNERRead moreKennedy Box Spanners – Metric
Metric
Manufactured from high quality steel tube. Zinc plated for corrosion resistance, each supplied with tommy bar. -
8mmx9mm OFFSET RATCHET RING SPANNERRead moreKennedy Reversible Ratchet Ring Wrenches, 25° Offset – Metric
25° Offset: Metric
For use where access is limited. With a built-in ratchet mechanism to provide speed and a reversible action which can be achieved by depressing the reversing lever or by simply turning the wrench over. All ratcheting ring wrenches are manufactured from chrome vanadium steel bi-hex rings.
*Single hexagon -
8mmx9mm STRAIGHT RATCHETRING WRENCHRead moreKennedy Reversible Ratchet Ring Wrenches, Straight – Metric
Straight: Metric
For use where access is limited. With a built-in ratchet mechanism to provide speed and a reversible action which can be achieved by depressing the reversing lever or by simply turning the wrench over. All ratcheting ring wrenches are manufactured from chrome vanadium steel bi-hex rings. -
8mmx9mm WORKSHOP OPEN END SPANNERRead moreOpen Jaw Spanners – Double-Ended
Double-Ended
Made from chrome vanadium steel with a black oxidised finish. Conform to DIN 895. -
8oz BLACK RUBBER MALLET WOOD SHAFTRead moreRubber Mallets
Soft faced for use where steel hammers would mark the surface. Provide a gentle but firm blow with little rebound. Solid hickory shafts. All purpose mallet used widely for automotive, industrial, DIY and camping etc.
-
8oz CROSS PEIN HAMMER WOOD SHAFTRead moreCross Pein Hammers
Cross pein hammers are traditionally used by joiners and fitters. Cross pein can be used for setting pins and nails prior to âdriving homeâ with the flat faced pein.
Warrington Hardwood Shaft
Close grained hardwood shaft shaped to comfortably fit in the hand. Forged steel head with ground and polished striking face. -
8×0.5mm ST/SH 4FL C/RADIUS END MILL Q-COATRead moreCarbide Plain Shank Corner Radius End Mills 4 Flute
Centre cutting.
To Manufacturers Standards.
Cutting diameter to e8.
Shank diameter to h6
ECQ-4PR Carbide Q-Coat.Series 86 Regular Length
-
8×1.0mm ST/SH 2FL C/RADIUS SLOT DRILL Q-COATRead moreSwissTech Carbide Plain Shank Corner Radius Slot Drills 2 Flute
Centre cutting.
To Manufacturers Standards.
Cutting diameter to e8.
Shank diameter to h6.
SCQ-2PR Carbide Q-Coat.Series 85 Regular Series
Dimensions to DIN 844. -
8×1.0mm ST/SH 4FL C/RADIUS END MILL Q-COATRead more
Carbide Plain Shank Corner Radius End Mills 4 Flute
Centre cutting.
To Manufacturers Standards.
Cutting diameter to e8.
Shank diameter to h6
ECQ-4PR Carbide Q-Coat.Series 86 Regular Length
-
8×1.1/2″ A2 ST/ST PIN HEX BUTTON SELF TAPPERRead moreTamper Hex Self-Tapping Security Screws
A2 Stainless Steel – Button Head