Archives: Products
Showing 8113–8128 of 23773 results
-
3.1/2″ A/F RING SLOGGINGWRENCHRead moreRing Slogging Spanners
Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. Manufactured to DIN 7444.
-
3.1/2″ FIBRE VICE GRIPS ( PR)Read moreKennedy Fibre Grips
Fibre-faced aluminium vice jaws for use with copper, aluminium, brass and wooden workpieces to prevent marking of work surface. Supplied in pairs.
-
3.1/2″ FOCAL LENGTH EYE LOUPERead moreKennedy Eye Loupes
Manufactured from shock resistant plastic. Shatterproof lens. Ideal for jewellers, watchmakers, electronics and model makers.
-
3.1/2″ HOOKED POINT LINO KNIFERead moreHooked Lino Knife
With heavy duty blade and quality wooden handle. For cutting linoleum and comparable materials.
-
3.1/2″x3″x2.1/2″ WEBBED ANGLE PLATERead moreOxford Precision Angle Plates – Webbed End
Webbed End
Webbed slotted angle plates can be used for rapid mounting fixtures for machine set-up, layout, or inspection. They are heavily ribbed for strength and rigidity. Sides and ends are machine finished. Manufactured from close grained cast iron. BS : 5535 Grade B. -
3.1/2″x4.1/2″ WRITE-ON GRIPSEAL BAGSRead moreAvon? Gripseal Polythene Bags – Write On
Medium weight. With three write-on stripes. Pack of 1000.
-
3.1/2oz CROSS PEIN HAMMER HICKORY SHAFTRead moreCross Pein Hammers
Cross pein hammers are traditionally used by joiners and fitters. Cross pein can be used for setting pins and nails prior to âdriving homeâ with the flat faced pein.
Hickory Shaft
Hardened and ground forged steel head with polished striking face securely fixed to a close grain hickory shaft. Shaped to fit comfortably in the hand. Tapered head, suitable for use with small pins helps reduce over-strike. -
3.1/2oz CROSS PEIN HAMMER WOOD SHAFTRead moreCross Pein Hammers
Cross pein hammers are traditionally used by joiners and fitters. Cross pein can be used for setting pins and nails prior to âdriving homeâ with the flat faced pein.
âPinâ Hardwood Shaft
Hardened and ground forged steel head with polished striking face securely fixed to a close grain hardwood shaft. Shaped to fit comfortably in the hand. Tapered head, suitable for use with small pins helps reduce over-strike. -
3.1/4″ A/F RING SLOGGINGWRENCHRead moreRing Slogging Spanners
Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. Manufactured to DIN 7444.
-
3.1/8″ A/F OPEN JAW SLOGGING WRENCHRead moreKennedy Open Jaw Slogging Spanners
Forged and hardened steel. Flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. To DIN 133.
-
3.1/8″ A/F RING SLOGGINGWRENCHRead moreRing Slogging Spanners
Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. Manufactured to DIN 7444.
-
3.10mm CARBIDE S/S JOBBER DRILLRp177.000Read moreSolid Carbide Jobber Drills
General purpose drills for drilling a wide variety of metallic and non-metallic materials.
Point angle: 118°. Tolerance of diameter: h7. Tolerance of shank: h6. Supply unit. All diameters – 1 pce.
Manufacturing Standard: BS 328, DIN 338. -
3.10mm CARBIDE S/S STUB DRILLRead moreSolid Carbide Stub Drills – Metric
Metric
For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic.
Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6.
Manufactured to Works Standard. -
3.10mm DIA COBALT DRILL FOR STAINLESS STEELRp33.000Read moreHSS-Co Straight Shank Drills
Metric
Heavy duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point angle: 135°. Helix angle: normal. Web thickness: strengthened. Relief angle: normal. Tolerance of diameter: h8. Tolerance of shank: f11. Supply unit. All diameters – 1 pce. Manufacturing Standard: BS 328, DIN 338B. -
3.10mm HEAVY DUTY COBALT DRILLRp44.000Read moreHSS-Co Straight Heavy Duty Drills
The addition of up to 8% cobalt allows higher speeds to be used without reducing the life of the tool, increasing productivity. 28° helix and 135° point. Manufactured to DIN 338 RN. Point to DIN 1412C.
-
3.10mm HEAVY DUTY COBALT L/SERIES DRILLRead moreHSS-Co Straight Shank Long Series Drills
Heavy-duty drill used for deep holes in steels with a tensile strength up to 1,400 N/mm2. Stainless steels, heat and acid-resistant steels and hard bronze. Point angle: 135°. Helix angle: normal. Web thickness: strengthened. Relief angle: normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufacturing Standard: DIN 340/BS328.