Archives: Products
Showing 7217–7232 of 23773 results
-
24mm LONG MULTI-TOOTH CUTTERRead moreM2 Multi-Tooth Milling Cutters
Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.
Sizes available: 2 – 52mm diameter short and 13 – 52mm diameter long series.Long Series
Shank diameter: 19mm/3/4â.
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm. -
24mm O/E CROWFOOT WRENCH3/8″ SQ. DRIVERead moreKennedy Crowfoot Wrenches, 3/8″
Chrome vanadium wrenches designed to be used for getting into tight spots and hard to reach areas, in particular around tubing such as hydraulic lines etc. For use with 3/8â square drive tools.
-
24mm O/E PODGER SPANNERRead moreKennedy Open End Podger Spanners
Designed to engage the nut from the side. As it only engages on two faces of the fastener, care must be taken to ensure that the correct size spanner is always used. Tapered handle for assisting with alignment of fixing holes on jigs and fabrications.
-
24mm OFFSET CV COMBINATION SPANNERRead moreKennedy Industrial Offset Combination Spanners – Metric
Metric
Chrome vanadium steel. 15° cranked open end. Offset ring end. Up to 25% longer than conventional DIN 3113 combination spanners. Conform to DIN 3113B. -
24mm OPEN JAW SLOGGING WRENCHRead moreKennedy Open Jaw Slogging Spanners
Forged and hardened steel. Flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. To DIN 133.
-
24mm PROFESSIONAL COMBINATION WRENCHRead moreKennedy Professional Combination Spanners – Metric
Metric
Manufactured from chrome vanadium steel with highly polished mirror finish. Mirror finish prevents oil and dirt from adhering to the spannermaking for easier cleaning and preventing rust. Long reach, wall drive. Conform with ANSE B107.6. -
24mm RATCHET COMBINATIONWRENCHRead moreKennedy Professional Ratchet Combination Spanners – Metric
Metric
Chrome vanadium steel with mirror polish finish, preventing oil and dirt from adhering to the spanner, making for easier cleaning and preventing rust. 72-teeth ratcheting system which needs only 5° movement to operate ratchet. Thin wall design for greater
access. Conform to ASME B107.6. -
24mm REVERSIBLE COMBINATION SPANNERRead moreKennedy Professional Reversible Combination Spanner – Metric
Metric
Bi-hexagonal 15 degree offset rings with a 72 teeth lever ratcheting system that requires only 5 degree movement to operate, making them ideal for use in tight areas. Made from high quality Chrome Vanadium Steel with mirror polish finish to prevent oil and dirt from adhering to the spanner. Heads conform to ASME B107.6. -
24mm RING CRANKED PODGERSPANNERRead moreKennedy Ring End Podger Spanners
Cranked handle assists with location of spanner on to fixings within a recess.
-
24mm RING SLOGGING WRENCHRead moreRing Slogging Spanners
Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. Manufactured to DIN 7444.
-
24mm SHORT MULTI-TOOTH CUTTERRead moreM2 Multi-Tooth Milling Cutters
Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.
Sizes available: 2 – 52mm diameter short and 13 – 52mm diameter long series.Short Series
Shank diameter: 19mm/3/4â.
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm. -
24mm SINGLE HEX SOCKET 1/2″ SQ DRRead moreKennedy Single-Hexagon Standard Length Sockets, 1/2″
Single-Hexagon Sockets
Six point – offer a more positive location, particularly on worn or rounded nuts, but require a one-sixth turn to engage the next point of the socket. -
24mm SOCKET 1/2″ SQ DRRead moreKennedy Bi-Hexagon Standard Length Sockets, 1/2″
Bi-Hexagon Sockets
12 point – side drive design gives a higher torque than normal sockets, grip worn nuts and will not round off existing nuts. All have a ball-retaining groove on each face of the square drive, which ensures a positive fit with accessories. Require only a one-twelfth turn to engage the next point of the socket. -
24mm SOCKET 1/2″ SQUARE DRIVERead moreYamoto Bi-Hexagon Standard Length Sockets, 1/2″
Bi-Hexagon Sockets
12 point – side drive design gives a higher torque than normal sockets, grip worn nuts and will not round off existing nuts. All have a ball-retaining groove on each face of the square drive, which ensures a positive fit with accessories. Require only a one-twelfth turn to engage the next point of the socket. -
24mm SOCKET 3/4″ SQ DRRead moreKennedy Bi-Hexagon Sockets, 3/4″ – Metric
Metric
A heavy duty range designed to cope with the demands of industrial agricultural machinery and heavy plant, static or mobile. All Kennedy Professional sockets have a unique double knurl to give a high grip essential for a quick tool change when hands are greasy. Manufactured from chrome vanadium and fully chrome plated with a mirror finish and aluminium-free to ensure non-sparking. Chamfered leading edge ensures easy fastener location. Registered Design No. 2053516UK. -
24mm SPARK RESISTANT COMBINATION SPANNER Al-BrRead moreKennedy Professional Aluminium-Bronze Spark-Resistant Safety Tools: Combination Spanners
Combination Spanners
Spark-resistant tools are used to eliminate the chances of accidental fires or explosions in potentially combustible or explosive environments. They resist the sparks that a standard tool could potentially create when striking hard surfaces. The use of spark resistant tools is essential in many industrial applications such as petroleum and chemical manufacturing, spray booth operations, the marine industry, the mining industry, the paper industries, or any location where flammable vapours or combustible residues are present. Aluminium-bronze spark resistant safety tools are manufactured to 25HRC and offer a breaking strain of 75 – 85kgf/mm2.
Spark-resistant tools must be maintained with special care. Frequent cleaning/re-dressing to remove ferrous particles or contaminants, which may impair the spark-resistant properties, is essential.