Archives: Products
Showing 6241–6256 of 23773 results
-
2.30mm HSS HARDENED/GROUND DRILL BLANKRead moreSherwood HSS Drill Blanks – Metric
Series J400 – Metric
Jobber length blank hardened and ground all over. Accurately ground without back taper.
Diameter tolerance: h8. Manufactured to DIN 338. -
2.30mm HSS S/S BRIGHT JOBBER DRILLRp118.000Read moreSherwood HSS Jobber Drills Metric, Bright Finish – Metric
Series J100 – Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10°-20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328/DIN338RN.Bright Finish
Drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials. -
2.30mm HSS S/S BRIGHT L/S DRILLRead moreHSS Straight Shank Long Series Drills – Bright Finish
General purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron,
malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, web thickness: normal,
relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of f11. Manufactured to BS 328; Part 1: 1986, DIN 340 RN, ISO 494. Drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials -
2.30mm HSS S/S JOBBER DRILLRp87.000Read moreSherwood HSS Jobber Drills Steam Tempered – Metric
Series J100 – Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328/DIN338RN.Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining. -
2.30mm HSS S/S L/S DRILLRp25.000Read moreHSS Straight Shank Long Series Drills – Steam Tempered
General purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, web thickness: normal, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of f11. Manufactured to BS 328; Part 1: 1986, DIN 340 RN, ISO 494.
-
2.30mm HSS S/S STUB DRILLRead moreSherwood HSS General Purpose Stub Drills – Metric Sizes
Series S100 – Metric
General purpose drills for use on automatics and turret lathes. Suitable for drilling steels, cast iron, alloy steel and malleable cast iron. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BSâ328: Part 1: 1986/DIN 1897. -
2.30mm TiN TIPPED JOBBER DRILLRp12.000Read moreSwissTech HSS Straight Shank TiN Tipped Jobber Drills – Metric
Metric
Bright body with TiN coating on working part. For drilling in steel, cast steel alloyed and non-alloyed, grey cast iron, graphite and malleable cast iron. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: normal, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328, DIN 338. -
2.35mm HSS S/S JOBBER DRILLRp101.000Read moreSherwood HSS Jobber Drills Steam Tempered – Metric
Series J100 – Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328/DIN338RN.Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining. -
2.3KVA/5.5HP FULL FRAME GENERATOR TANK CAP. 12LTRRead moreKobe⢠Portable Petrol Generator
GPP230
⢠Ideal for builders, contractors, mobile caterers, etc.
⢠Powers lighting, freezers, power tools, water pumps and other electrical items.
⢠Brushless alternator type.
⢠2.3kVA/2.3kW maximum power.
⢠2kVA/2kW Continuous power
⢠One 220V AC and one 110V AC outlet.
⢠Voltmeter.
⢠Circuit breakers.
⢠12ltr fuel tank with fuel level indicator.
⢠Approximately 9hrs running time.
⢠Motor: 4-stroke, 6.0hp, OHV, single cylinder, air cooled engine that runs on unleaded petrol.
⢠Low oil alert and shutdown.
⢠Recoil starter.
⢠Anti-vibration mounts.
Dimensions (H x W x D): 425 x 515 x 430mm.
Weight: 42kg. -
2.3mm DIN 6799 ‘E’ CIRCLIPS (PACK 200)Read moreQualfast E-Clips
E-clips simplify designs and linked with lower installation costs are the ideal item for replacing more traditional fasteners. All are manufactured from carbon steel with a phosphate finish. Conform to DIN 6799.
-
2.4 x 4mm ALUMINIUM DOME HEAD RIVET (BOX 100)Read moreAluminium Rivets: Dome Head
Dome Head
For all applications of blind riveting. Aluminium rivet head with steel mandrel. Medium strength, use with aluminium and where rust is a problem. Select grip based on thickness of material to be riveted. -
2.4 x 6mm ALUMINIUM DOME HEAD RIVET (BOX 100)Read more
Aluminium Rivets: Dome Head
Dome Head
For all applications of blind riveting. Aluminium rivet head with steel mandrel. Medium strength, use with aluminium and where rust is a problem. Select grip based on thickness of material to be riveted. -
2.4 x 8mm ALUMINIUM DOME HEAD RIVET (BOX 100)Read more
Aluminium Rivets: Dome Head
Dome Head
For all applications of blind riveting. Aluminium rivet head with steel mandrel. Medium strength, use with aluminium and where rust is a problem. Select grip based on thickness of material to be riveted. -
2.40mm CARBIDE S/S JOBBER DRILLRp139.000Read moreSolid Carbide Jobber Drills
General purpose drills for drilling a wide variety of metallic and non-metallic materials.
Point angle: 118°. Tolerance of diameter: h7. Tolerance of shank: h6. Supply unit. All diameters – 1 pce.
Manufacturing Standard: BS 328, DIN 338. -
2.40mm CARBIDE S/S STUB DRILLRp103.000Read moreSolid Carbide Stub Drills – Metric
Metric
For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic.
Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6.
Manufactured to Works Standard. -
2.40mm DIA COBALT DRILL FOR STAINLESS STEELRp22.000Read moreHSS-Co Straight Shank Drills
Metric
Heavy duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point angle: 135°. Helix angle: normal. Web thickness: strengthened. Relief angle: normal. Tolerance of diameter: h8. Tolerance of shank: f11. Supply unit. All diameters – 1 pce. Manufacturing Standard: BS 328, DIN 338B.