Archives: Products
Showing 20209–20224 of 23773 results
-
M8x1.25 WHITE 371 HSS-EV NIT THROUGH TAPRead moreHSS âWhite Ringâ Taps
Manufactured to DIN 371/376
Suitable for the following Material Groups
Straight Flute – HSS-EV Nitride Finish
For through holes. Taper lead to
DIN form D (taper) (3.5 x P to 5 x P).
Tapping tolerance to 6HX. -
M8x1.25 YELLOW SP/FL 371 HSS-EV OX TAPRead moreHSS-EV ‘Yellow Ring’ Taps
Spiral Flute – HSS-EV Oxidised Finish
For blind holes.
Taper lead to DIN form C (3 x P).
Tapping tolerance:
Spiral flute to 6H.Suitable for the following Material Groups;
1.1
Mild soft steel & free machining non-alloy low carbon steel.
1.2
Non-alloy case hardening, structural & low to medium carbon steel.
1.3
Non-alloy, plain and medium carbon steel and castings -
M8x1.25 YELLOW SP/PT 371 HSS-EV OX TAPRead moreHSS-EV ‘Yellow Ring’ Taps
Spiral Point/Gun Nose –
HSS-EV Oxidised Finish
For through holes.
Taper lead to DIN form B.
(3.5 x P to 5.5 x P).
Tapping tolerance to 6H.Suitable for the following Material Groups;
1.1
Mild soft steel & free machining non-alloy low carbon steel.
1.2
Non-alloy case hardening, structural & low to medium carbon steel.
1.3
Non-alloy, plain and medium carbon steel and castings -
M8x1.25mm 45 DEG ANGLE HYDRAULIC NIPPLESRead moreKennedy Hydraulic Grease Nipples – 45° Type
For use with Kennedy grease guns and all other hydraulic grease equipment.
-
M8x1.25mm 90 DEG ANGLE HYDRAULIC NIPPLESRead moreHydraulic Grease Nipples – 90° Type
For use with Kennedy grease guns and all other hydraulic grease equipment.
-
M8x1.25mm CHASER DIE 12mm D/HD TYPE S20Read moreCoventry Type Chaser Dies – ISO Metric: Throat Angle S20
Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again.
Throat Angles
20° for general work and soft steels – supplied as standard.
33° âBâ type for cutting brass, available on request.Grinding Dies
Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used.Marking & Materials
Each die is marked with: diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die. -
M8x1.25mm CHASER DIE 20mm D/HD TYPE S20Read moreCoventry Type Chaser Dies – ISO Metric: Throat Angle S20
Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again.
Throat Angles
20° for general work and soft steels – supplied as standard.
33° âBâ type for cutting brass, available on request.Grinding Dies
Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used.Marking & Materials
Each die is marked with: diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die. -
M8x1.25mm STRAIGHT HYDRAULIC NIPPLESRead moreHydraulic Grease Nipples – Straight-Type
For use with Kennedy grease guns and all other hydraulic grease equipment.
-
M8x12 A2 ST/ST PIN HEX BUTTON M/C SCREWRead moreTamper Hex Security Screws: A2 Stainless Steel – Button Head
A2 Stainless Steel – Button Head
Pin Hex security screws with internal pin within the socket – prevents the use of standard hex keys. Suitable for medium torque applications. -
M8x12 A2 ST/ST TAMPER TORX BUTTON M/C SCREWRead moreTamper Torx Security Screws
A2 Stainless Steel – Button Head
-
M8x16 A2 ST/ST PIN HEX BUTTON M/C SCREWRead more
Tamper Hex Security Screws: A2 Stainless Steel – Button Head
A2 Stainless Steel – Button Head
Pin Hex security screws with internal pin within the socket – prevents the use of standard hex keys. Suitable for medium torque applications. -
M8x16 A2 ST/ST PIN HEX CSK M/C SCREWRead moreTamper Hex Security Screws – A2 Stainless Steel – Countersunk
A2 Stainless Steel – Countersunk
Pin Hex security screws with internal pin within the socket – prevents the use of standard hex keys. Suitable for medium torque applications. -
M8x16 A2 ST/ST TAMPER TORX BUTTON M/C SCREWRead more
Tamper Torx Security Screws
A2 Stainless Steel – Button Head
-
M8x20 A2 ST/ST PIN HEX BUTTON M/C SCREWRead more
Tamper Hex Security Screws: A2 Stainless Steel – Button Head
A2 Stainless Steel – Button Head
Pin Hex security screws with internal pin within the socket – prevents the use of standard hex keys. Suitable for medium torque applications. -
M8x20 A2 ST/ST PIN HEX CSK M/C SCREWRead more
Tamper Hex Security Screws – A2 Stainless Steel – Countersunk
A2 Stainless Steel – Countersunk
Pin Hex security screws with internal pin within the socket – prevents the use of standard hex keys. Suitable for medium torque applications. -
M8x20 A2 ST/ST TAMPER TORX BUTTON M/C SCREWRead more
Tamper Torx Security Screws
A2 Stainless Steel – Button Head