Archives: Products
Showing 19393–19408 of 23773 results
-
M4x0.7 OR. SP/FL 371 HSS-PM NIT+OX TAPRead moreHSS âOrange Ringâ Taps
Spiral Flute – HSS-PM Nitride & Oxide Finish
For blind holes. Taper lead to DIN form C.
This tap has the special
chamfer lead of (3 x P).
Tapping tolerance: spiral flute to 6H.
ISO Metric Coarse Helix angle 40°. Tapping depth 2.5 x D. -
M4x0.7 OR. SP/PT 371 HSS-PM NIT+OX TAPRead moreHSS ‘Orange Ring’ Taps
Spiral Point/Gun Nose –
HSS-PM Nitride & Oxide Finish
For through holes.
Taper lead to DIN form B
(3.5 x P to 5.5 x P).
Tapping tolerance to 6HX.
ISO Metric CoarseSuitable for the following Material Groups;
4.3
Titanium alloys of a hard and very hard to machine nature.
5.1
Heat resistant super alloys including iron based high temperature alloys.
5.2
Heat resistant super alloys, cobalt or nickel based hard to very hard to machine -
M4x0.7 PURPLE SP/FL 371 HSS-PM NIT TAPRead moreHSS âPurple Ringâ Taps
Right Hand Cutting – Left Hand
Spiral Flute – HSS-PM Nitride Finish
For through holes. Left hand spiral.
Taper lead to DIN form D (3.5 x P to 5 x P).
Tapping tolerance to 6HX.
ISO Metric Coarse Helix angle 15°. -
M4x0.7 PURPLE SP/FL 371 HSS-PM NIT TAPRead moreHSS âPurple Ringâ Taps
Spiral Flute – HSS-PM Nitride Finish
For blind holes. Taper lead to DIN form B
(3 x P). Tapping tolerance to 6HX.
ISO Metric Coarse Helix angle 15°. Tapping depth 2.5 x D. -
M4x0.7 RED RING SP/FL DIN 371 HSS-EV OX TAPRead moreSpiral Flute – HSS-EV
Oxidised Finish
For blind holes.
Taper lead to DIN form C (3 x P).
Tapping tolerance:
spiral flute to 6H.
ISO Metric Coarse
Helix angle 40°. Tapping depth 2.5 x D. -
M4x0.7 RED RING SP/PT DIN 371 HSS-EV BRT TAPRead moreHSS âRed Ringâ Taps
Manufactured to DIN 371/376
Suitable for the following Material Groups
Spiral Point/Gun Nose –
HSS-Co Bright Finish
For through holes.
Taper lead to DIN form B
(3.5 x P to 5.5 x P).
Tapping tolerance to 6HX.
ISO Metric Coarse -
M4x0.7 WHITE 371 HSS-EV NIT BLIND TAPRead moreHSS âWhite Ringâ Taps
Straight Flute – HSS-EV Nitride Finish
For blind holes. Plug/bottoming lead to
DIN form C (2 x P to 3 x P).
Tapping tolerance to 6HX. -
M4x0.7 WHITE 371 HSS-EV NIT THROUGH TAPRead more
HSS âWhite Ringâ Taps
Manufactured to DIN 371/376
Suitable for the following Material Groups
Straight Flute – HSS-EV Nitride Finish
For through holes. Taper lead to
DIN form D (taper) (3.5 x P to 5 x P).
Tapping tolerance to 6HX. -
M4x0.7 YELLOW SP/FL 371 HSS-EV OX TAPRead moreHSS-EV ‘Yellow Ring’ Taps
Spiral Flute – HSS-EV Oxidised Finish
For blind holes.
Taper lead to DIN form C (3 x P).
Tapping tolerance:
Spiral flute to 6H.Suitable for the following Material Groups;
1.1
Mild soft steel & free machining non-alloy low carbon steel.
1.2
Non-alloy case hardening, structural & low to medium carbon steel.
1.3
Non-alloy, plain and medium carbon steel and castings -
M4x0.70 YELLOW SP/PT 371 HSS-EV OX TAPRead moreHSS-EV ‘Yellow Ring’ Taps
Spiral Point/Gun Nose –
HSS-EV Oxidised Finish
For through holes.
Taper lead to DIN form B.
(3.5 x P to 5.5 x P).
Tapping tolerance to 6H.Suitable for the following Material Groups;
1.1
Mild soft steel & free machining non-alloy low carbon steel.
1.2
Non-alloy case hardening, structural & low to medium carbon steel.
1.3
Non-alloy, plain and medium carbon steel and castings -
M4x0.70mm CHASER DIE 12mm D/HD TYPE S20Read moreCoventry Type Chaser Dies – ISO Metric: Throat Angle S20
Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again.
Throat Angles
20° for general work and soft steels – supplied as standard.
33° âBâ type for cutting brass, available on request.Grinding Dies
Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used.Marking & Materials
Each die is marked with: diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die. -
M4x0.70mm CHASER DIE 6mmD/HD TYPE S20Read moreCoventry Type Chaser Dies – ISO Metric: Throat Angle S20
Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again.
Throat Angles
20° for general work and soft steels – supplied as standard.
33° âBâ type for cutting brass, available on request.Grinding Dies
Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used.Marking & Materials
Each die is marked with: diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die. -
M4x10 A2 ST/ST TAMPER TORX BUTTON M/C SCREWRead moreTamper Torx Security Screws
A2 Stainless Steel – Button Head
-
M4x10 A2 ST/ST TAMPER TORX CSK M/C SCREWRead moreTamper Torx Security Screws
A2 Stainless Steel – Countersunk
-
M4x12 A2 ST/ST TAMPER TORX BUTTON M/C SCREWRead more
Tamper Torx Security Screws
A2 Stainless Steel – Button Head
-
M4x12 A2 ST/ST TAMPER TORX CSK M/C SCREWRead more
Tamper Torx Security Screws
A2 Stainless Steel – Countersunk