Archives: Products
Showing 14817–14832 of 23773 results
-
80mm B/H SWIVEL CASTOR R/T WHEEL BLACKRead moreBlack Rubber Tyre – Swivel Type with Bolt Hole Zinc
Suitable for use on most surfaces. Suitable for humid environments where medium harsh chemicals may be present. Quiet running with “cushioned” tyre. Not recommended for use where mineral or organic acids are present. Operating temperature range -20C to 60C.
-
80mm BLACK RUBBER TYRE STEEL CENTRERead moreBlack Rubber Wheel Only
For smooth running with heavier loads. Suitable for use on most surfaces. Suitable for humid environments where medium harsh chemicals may be present. Quiet running with “cushioned” tyre. Not recommended for use where mineral or organic acids are present. Operating temperature range -20C to 60C.
-
80mm CARBIDE TIPPED HOLESAWRead moreCarbide Tipped Holesaws
Kennedy® carbide tipped hole saws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel. Use standard arbors.
-
80mm CHROME VANADIUM COMBINATION SPANNERRead moreKennedy Industrial Combination Spanners – Metric
Metric
Manufactured from chrome vanadium steel with a satin finish body and highly polished heads. 15 open jaw angle to shank and ring end offset.
Conform to:
5.5mm – 25mm, 1/4″ – 1″ AF – DIN 3113.
26mm – 50mm, 11/16″ – 2″AF – ASME B107.6.
1/8″ – 1/2″ Whitworth – DIN 3113 & BS192:1982.
9/16″ – 7/8″ Whitworth – ASME B107.6 & BS192:1982. -
80mm DEEP IMPACT SOCKET 1″ SQ DRRead moreKennedy Chrome Molybdenum Impact Sockets: 1″ Drive Metric, Deep Length, 6-Point
1â Drive Metric, Deep Length, 6-Point
Conform to: DIN 3129.Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.
-
80mm GREY RUBBER PLASTICTYRE-PLAIN BORERead moreGrey Rubber Wheel Only
Suitable for use on hard floors (cement, tiles, etc). Non marking rubber tyre. Quiet running with “cushioned” tyre Suitable for humid environments where medium harsh chemicals may be present. Not recommended for use with organic solvents, chlorinated substances, hydrocarbons or mineral oils. Operating temperature range -20C to 60C.
-
80mm IMPACT SOCKET 1-1/2″ DRRead moreChrome Molybdenum Impact Sockets: 1 1/2″ Drive Metric Size, Standard Length, 6-Point
1 1/2″ Drive Metric Size, Standard Length, 6-Point
Conform to: SAE, USA Federal Standard GGG-W-660A.Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.
-
80mm IMPACT SOCKET 1″ SQDRRead moreKennedy Chrome Molybdenum Impact Sockets: 1″ Drive Metric, Standard Length, 6-Point
Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.
-
80mm NYLON PLAIN BORE WHEEL x 40 HUBRead moreNylon Wheel Only
Suitable for use on compact floors (cement, tiles, etc). Particularly recommended for the food processing industry. Not recommended for use where mineral or organic acids are present. Operating temperature range -10C to 60C.
-
80mm OPEN JAW SLOGGING WRENCHRead moreKennedy Open Jaw Slogging Spanners
Forged and hardened steel. Flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. To DIN 133.
-
80mm POLY TYRE/NYLON CENTRE WHEEL PL/BRRead moreRed Polyurethane Wheel Only
Suitable for use on most surfaces. Suitable for humid environments where medium harsh chemicals may be present. Quiet running with “cushioned” tyre. Not recommended for use where mineral or organic acids are present. Operating temperature range -20C to 80C.
-
80mm QUICK GRIP DRILL PRESS VICE FIXED JAWRead moreIndexa Quick Grip Drill Press Vices
Fixed Jaw
Quick acting cam can be set instantly to hold work. Fixed jaw with V-block to handle flat or round pieces, vertically or horizontally. Jaw inserts are hardened and ground. The heavy base can be clamped down to a milling machine or drill press. -
80mm RING SLOGGING WRENCHRead moreRing Slogging Spanners
Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. Manufactured to DIN 7444.
-
80mm SOCKET 1″ SQ DRRead moreKennedy Bi-Hexagon Standard Sockets, 1″
Bi-hexagon. (12 point). This range of 1â (25mm) series sockets is the ultimate for high torque hand applications. The Bi-hexagon design gives strength and reliability under heavy loads. Used extensively in heavy plant, rail, shipyard and oil rig industries. The 12 point bi-hexagon side drive design gives a higher torque than normal sockets. Made from chrome vanadium and fully chrome plated with a mirror finish. Aluminium-free to ensure non-sparking. Chamfered leading edge ensures easy fastener location.
-
80mm SPARK RESISTANT R/END SLOGGING WRENCH Al-BrRead moreAluminium-Bronze Spark-Resistant Safety Tools: Ring End Slogging Wrench
Ring End Slogging Wrench
With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners.Spark-resistant tools are used to eliminate the chances of accidental fires or explosions in potentially combustible or explosive environments. They resist the sparks that a standard tool could potentially create when striking hard surfaces. The use of spark resistant tools is essential in many industrial applications such as petroleum and chemical manufacturing, spray booth operations, the marine industry, the mining industry, the paper industries, or any location where flammable vapours or combustible residues are present. Aluminium-bronze spark resistant safety tools are manufactured to 25HRC and offer a breaking strain of 75 – 85kgf/mm2.
Spark-resistant tools must be maintained with special care. Frequent cleaning/re-dressing to remove ferrous particles or contaminants, which may impair the spark-resistant properties, is essential. -
80mm SWIVEL PATTERN ROPESPRING HOOKS (PAIR)Read moreSwivel Spring Hooks
Connectors for ropes and chains, with swivel to allow revolving and prevent knotting and twisting. Zinc plated.