Archives: Products
Showing 10561–10576 of 23773 results
-
4″x5.1/2″ WRITE-ON GRIPSEAL BAGSRead moreAvon? Gripseal Polythene Bags – Write On
Medium weight. With three write-on stripes. Pack of 1000.
-
4″x5/32″x1″ HSS SLITTINGSAW 100TRead moreSherwood HSS Slitting Saws Fine/Coarse – Inch
High speed steel slitting saws are hollow ground to give the clearance necessary for deep cutting. Available in coarse and fine teeth, number of teeth specified below. Supplied with keyways as standard. Manufactured to BS122.
-
4″x5/64″x1″ HSS SLITTINGSAW 100TRead moreSherwood HSS Slitting Saws Fine/Coarse – Inch
High speed steel slitting saws are hollow ground to give the clearance necessary for deep cutting. Available in coarse and fine teeth, number of teeth specified below. Supplied with keyways as standard. Manufactured to BS122.
-
4″x5/64″x1″ HSS SLITTINGSAW 36TRead moreSherwood HSS Slitting Saws Fine/Coarse – Inch
High speed steel slitting saws are hollow ground to give the clearance necessary for deep cutting. Available in coarse and fine teeth, number of teeth specified below. Supplied with keyways as standard. Manufactured to BS122.
-
4″x9″ CONTRACTOR BRICK BOLSTERRead moreContractor Brick Bolster Chisels
Chrome vanadium – used for splitting bricks.
-
4″x9″ CONTRACTOR BRICK BOLSTER C/W GUARDRead moreContractor Brick Bolster Chisels
Chrome vanadium – used for splitting bricks.
-
4% CONTRACT BLEACH 5LTRRead moreContract Bleach
A solution containing 4% sodium hypochlorite, for use in toilets, sinks and drains.
-
40 P20/P30 BRAZED TOOLRp178.000Read moreKennedy Light Turning & Boring Tools – P30
Brazed Tip Turning & Boring Tools
Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40: Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30: Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20: General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates. -
40-80mm PURPLE H. ST. SLEEVING (50 MTR REEL)Read moreGlobal Protective Sleeving
Exceptional, effective and economical protection for all kinds of products. Ideal protection for machined components during production and storage. Also widely used to protect ceramics, glass and other fragile components/products through storage and distribution. Designed to help prevent both surface and impact damage.’Cushion’ products during transportation. 6 colour-coded sizes. High stretch capability handles products/components up to 400mm diameter.
Exceptional formability and flexibility means irregular and intricate shapes can be protected.
Supplied in purpose designed dispenser cartons. -
40-PCE IMPACT DRIVER SET 1/2″ SQ. DR.Read moreKennedy Impact Driver Set – 40 Pieces
Industrial quality impact driver with switchable forward and reverse screwdriver rotation. When the impact resistant handle is struck with a hammer the downward force is converted by the impact driverâs internal mechanism into a powerful high torque screwdriver rotation action. Ideal for ensuring fasteners are securely tightened and for freeing stuck fasteners. Hex drive nose pieces can be removed to allow use with 1/2â square drive impact sockets.
40-Piece Impact Driver Set
1/2â square to 5/16â hexagon bit adaptor 1/2â square to 3/8â hexagon bit adaptor.
80mm x 3/8â Hexagon bits, Hexagon: 8mm, 6mm, TX: Tx40, Tx45, Tx50, Crosspoint: No.2, No.3, Slotted: 8mm and 10mm.
35mm x 3/8â Hexagon bits, Hexagon: 4mm, 5mm, 6mm, 7mm, 8mm, TX: Tx20, Tx25, Tx30, Tx40, Tx45, Tx50, Crosspoint: No.1, 2, 3 & 4, Slotted: 5mm, 6mm, 8mm, 10mm, 12mm.
30mm x 5/16â Hexagon bits, Hexagon: 10mm, 12mm, TX: Tx55, Spline: 5mm, 6mm, 8mm, 10mm, and 12mm. -
40-PCE TORX, HEX & SPLINE BIT SETRead moreKennedy 10mm Hexagon Power Bit Set – 40 Pieces
This Impact Driver Bit Set is suitable for workshop and manufacturing use. Made from chrome molybdenum the range includes Hexagon, TX and Spline bits with 3/8â and 1/2â x 10mm Bit Adaptors that are suitable for hand and power impact drivers.
Contents:
3/8â and 1/2â Square x 10mm Hexagon Bit Adaptors.
75mm x 10mm Hexagon bits:
Hexagon: 4, 5, 6, 7, 8, 10 and 12mm.
TX: Tx20, Tx25, Tx30, Tx40, Tx45, Tx50 and Tx55.
Spline: 5, 6, 8, 10 and 12mm.
30mm x 10mm Hexagon bits:
Hexagon: 4, 5, 6, 7, 8, 10 and 12mm.
TX: Tx20, Tx25, Tx30, Tx40, Tx45, Tx50 and Tx55.
Spline: 5, 6, 8, 10 and 12mm. -
40.00mm HSS SP/FL PARALLEL HAND REAMERRp5.953.000Read moreStraight Shank Parallel Hand Reamers
Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.
Metric Tolerances
Diameter: ~ up to 3.00. Tolerance: +0.008, -0.007.
Diameter: Over 3.00 ~ up to 6.00. Tolerance: +0.010, -0.005.
Diameter: Over 6.00 ~ up to 10.00. Tolerance: +0.012, -0.006.
Diameter: Over 10.00 ~ up to 18.00. Tolerance: +0.015, -0.008.
Diameter: Over 18.00 ~ up to 30.00. Tolerance: +0.017, -0.009.
Diameter: Over 30.00 ~ up to 50.00. Tolerance: +0.021, -0.012. -
40.00mm HSS T/S DRILLRp2.568.000Read moreSherwood HSS Taper Shank Drills, 4 Morse Taper – Metric
Series T100
General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345. -
40.00mm HSS T/S SP/FL MACHINE REAMERRead moreTaper Shank Machine Reamers
Used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head. Manufactured to BS 328-4.
Tolerances (to H7)
Diameter: ~ up to 3.00. Tolerance: +0.008, -0.007.
Diameter: Over 3.00 ~ up to 6.00. Tolerance: +0.010, -0.005.
Diameter: Over 6.00 ~ up to 10.00. Tolerance: +0.012, -0.006.
Diameter: Over 10.00 ~ up to 18.00. Tolerance: +0.015, -0.008.
Diameter: Over 18.00 ~ up to 30.00. Tolerance: +0.017, -0.009.
Diameter: Over 30.00 ~ up to 50.00. Tolerance: +0.021, -0.012.
Diameter: Over 50.00 ~ up to 80.00. Tolerance: +0.025, -0.014.
Diameter: Over 80.00 ~ up to 120.00. Tolerance: +0.029, -0.016. -
40.00mm x 555mm O/A HSS TAPER SHANK DRILLRead moreHSS Extra Length Taper Shank Drills to BS328 : 1 1986 – 3 Morse Taper, Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite.
Point angle 118°, helix angle: normal, web thickness: standard, relief angle 8° – 20°, tolerance of diameter: h8.
Made to BS328 : 1 1986. Sizes 32mm to 50mm are made to DIN1870/Series 1. -
40.5x57x35mm POWER MAGNETRead moreKennedy Power Magnets
A square horseshoe magnet. Supplied with plain fixing holes.
Kg pull (max): 25mm – 4.5, 30mm – 9.0, 40mm – 11.8.