Archives: Products
Showing 7601–7616 of 23773 results
-
25×6.5mm FELT LAPPING WHEELRead moreFelt Polishing Bobs
Suitable for use with Kobe, Dremel and Osaki Multi Tools
Felt Polishing Bobs
For use with polishing compounds to produce a high finish. Use with spindle shown below. -
26 P20/P30 BRAZED TOOLRead moreKennedy Cranked Round Nosed Turning Tools – P30
Brazed Tip Turning & Boring Tools
Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40: Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30: Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20: General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates. -
26-40mm TAPERED SHEET & TUBE DRILLRead moreSherwood HSS Taper Sheet & Tube Drills
For producing clean holes in sheet metal and other thin-walled materials. Efficient cutting geometry, no pre-drilled pilot hole and the diameter of the finished hole is infinitely variable within the range of each drill, according to depth of feed.
-
26-50mm CV COMBINATION SPANNER SET 11PCRead moreKennedy Spanner Sets
Kennedy combination spanners are manufactured from chrome vanadium steel with a satin finish body and highly polished heads. 15 open jaw angle to shank and ring end offset.
Conform to:
5.5mm – 25mm, 1/4 inch – 1 inch, AF – DIN 3113.
26mm – 50mm, 11/16 inch – 2 inch, AF – ASME B107.6. -
26.0 x 250mm SDS-PLUS HAMMER DRILL BITRp552.000Read moreSDS-Style Fitting Hammer Drill Bits
Tungsten carbide tipped SDS masonry drills are suitable for all SDS direct fitting hammer drills. High performance drill bits that withstand extreme heat generation ensuring maximum performance coupled with wear resistance. Manufactured to DIN 8035.
-
26.0 x 450mm SDS-PLUS HAMMER DRILL BITRp434.000Read more
SDS-Style Fitting Hammer Drill Bits
Tungsten carbide tipped SDS masonry drills are suitable for all SDS direct fitting hammer drills. High performance drill bits that withstand extreme heat generation ensuring maximum performance coupled with wear resistance. Manufactured to DIN 8035.
-
26.0-25.0 ER40 SINGLE ANGLE COLLETRead moreER – Single Angle Collets
Manufactured from hardened and tempered high alloy steel.
Conform to DIN 6499. -
26.00mm HSS 1/2″ PARALLEL SHANK DRILLRp567.000Read moreHSS Reduced Shank Drills (Blacksmiths)
1/2â parallel shank. General purpose drills for light duty work, for drilling steels, cast iron, nickel brass and graphite. Reduced parallel shank 1/2â. Point angle: 118°, helix angle: normal, web thickness: standard, tolerance of diameter: h8, tolerance of shank: 0.01/0.08. Manufactured to works standard.
-
26.00mm HSS T/S DRILLRp842.000Add to cartSherwood HSS Taper Shank Drills, 3 Morse Taper – Metric
Series T100
General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345. -
26.00mm HSS T/S SP/FL MACHINE REAMERRp2.577.000Read moreTaper Shank Machine Reamers
Used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head. Manufactured to BS 328-4.
Tolerances (to H7)
Diameter: ~ up to 3.00. Tolerance: +0.008, -0.007.
Diameter: Over 3.00 ~ up to 6.00. Tolerance: +0.010, -0.005.
Diameter: Over 6.00 ~ up to 10.00. Tolerance: +0.012, -0.006.
Diameter: Over 10.00 ~ up to 18.00. Tolerance: +0.015, -0.008.
Diameter: Over 18.00 ~ up to 30.00. Tolerance: +0.017, -0.009.
Diameter: Over 30.00 ~ up to 50.00. Tolerance: +0.021, -0.012.
Diameter: Over 50.00 ~ up to 80.00. Tolerance: +0.025, -0.014.
Diameter: Over 80.00 ~ up to 120.00. Tolerance: +0.029, -0.016. -
26.00mm x 400mm O/A HSS TAPER SHANK DRILLRead moreHSS Extra Length Taper Shank Drills to BS328 : 1 1986 – 3 Morse Taper, Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite.
Point angle 118°, helix angle: normal, web thickness: standard, relief angle 8° – 20°, tolerance of diameter: h8.
Made to BS328 : 1 1986. Sizes 32mm to 50mm are made to DIN1870/Series 1. -
26.00mm x 500mm O/A HSS TAPER SHANK DRILLRead more
HSS Extra Length Taper Shank Drills to BS328 : 1 1986 – 3 Morse Taper, Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite.
Point angle 118°, helix angle: normal, web thickness: standard, relief angle 8° – 20°, tolerance of diameter: h8.
Made to BS328 : 1 1986. Sizes 32mm to 50mm are made to DIN1870/Series 1. -
26.50mm HSS T/S DRILLRp862.000Read more
Sherwood HSS Taper Shank Drills, 3 Morse Taper – Metric
Series T100
General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345. -
260 K20 BRAZED TOOLRp253.000Read moreKennedy Parting Off Tools – K20
Brazed Tip Turning & Boring Tools
Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40: Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30: Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20: General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates. -
260 P20/P30 BRAZED TOOLRead more
Kennedy Parting Off Tools – P30
Brazed Tip Turning & Boring Tools
Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40: Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30: Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20: General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates. -
260 P40 BRAZED TOOLRead more
Kennedy Parting Off Tools – P40
Brazed Tip Turning & Boring Tools
Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40: Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30: Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20: General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.