Archives: Products
Showing 6433–6448 of 23773 results
-
2.9/16″ A/F OPEN JAW SLOGGING WRENCHRead moreKennedy Open Jaw Slogging Spanners
Forged and hardened steel. Flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. To DIN 133.
-
2.9/16″ A/F RING SLOGGING WRENCHRead moreRing Slogging Spanners
Manufactured from forged and hardened steel with machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners. Manufactured to DIN 7444.
-
2.90mm CARBIDE S/S JOBBER DRILLRp194.000Read moreSolid Carbide Jobber Drills
General purpose drills for drilling a wide variety of metallic and non-metallic materials.
Point angle: 118°. Tolerance of diameter: h7. Tolerance of shank: h6. Supply unit. All diameters – 1 pce.
Manufacturing Standard: BS 328, DIN 338. -
2.90mm CARBIDE S/S STUB DRILLRead moreSolid Carbide Stub Drills – Metric
Metric
For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic.
Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6.
Manufactured to Works Standard. -
2.90mm HEAVY DUTY COBALT DRILLRp44.000Read moreHSS-Co Straight Heavy Duty Drills
The addition of up to 8% cobalt allows higher speeds to be used without reducing the life of the tool, increasing productivity. 28° helix and 135° point. Manufactured to DIN 338 RN. Point to DIN 1412C.
-
2.90mm HEAVY DUTY COBALT STUB DRILLRp40.000Read moreHSS-Co Heavy Duty Cobalt Stub Drills
Series 2010 Metric
Heavy duty drill made of cobalt material with excellent heat resistance. For drilling steels up to 1,400N/mm2, stainless steel, heat resistant steels and bronze. Ideally suited for volume production on automatics. Point angle: 135°, helix angle: normal, web thickness: strengthened, tolerance of diameter: h8, tolerance of shank: f11.
Manufactured to BS 328, DIN 1897RN. Point to DIN 1412C. -
2.90mm HSS HARDENED/GROUND DRILL BLANKRead moreSherwood HSS Drill Blanks – Metric
Series J400 – Metric
Jobber length blank hardened and ground all over. Accurately ground without back taper.
Diameter tolerance: h8. Manufactured to DIN 338. -
2.90mm HSS S/S BRIGHT JOBBER DRILLRp128.000Read moreSherwood HSS Jobber Drills Metric, Bright Finish – Metric
Series J100 – Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10°-20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328/DIN338RN.Bright Finish
Drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials. -
2.90mm HSS S/S JOBBER DRILLRp83.000Read moreSherwood HSS Jobber Drills Steam Tempered – Metric
Series J100 – Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328/DIN338RN.Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining. -
2.90mm HSS S/S L/S DRILLRp28.000Read moreHSS Straight Shank Long Series Drills – Steam Tempered
General purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, web thickness: normal, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of f11. Manufactured to BS 328; Part 1: 1986, DIN 340 RN, ISO 494.
-
2.90mm HSS S/S STUB DRILLRead moreSherwood HSS General Purpose Stub Drills – Metric Sizes
Series S100 – Metric
General purpose drills for use on automatics and turret lathes. Suitable for drilling steels, cast iron, alloy steel and malleable cast iron. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BSâ328: Part 1: 1986/DIN 1897. -
2.90mm TiN TIPPED JOBBER DRILLRp12.000Read moreSwissTech HSS Straight Shank TiN Tipped Jobber Drills – Metric
Metric
Bright body with TiN coating on working part. For drilling in steel, cast steel alloyed and non-alloyed, grey cast iron, graphite and malleable cast iron. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: normal, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328, DIN 338. -
2.95mm HSS S/S JOBBER DRILLRp100.000Read moreSherwood HSS Jobber Drills Steam Tempered – Metric
Series J100 – Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328/DIN338RN.Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining. -
2.9mm CARBIDE S/S STUB DRILLRead moreKennedy Solid Carbide Stub Drills – Metric
Metric
For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic. Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6. Manufactured toâDIN 6539.Tolerances:
Cutting Dia. + 0.000mm – 0.015mm.
Shank Dia. + 0.000mm – 0.030mm. -
2″ A/F CHROME VANADIUM COMBINATION SPANNERRead moreKennedy Industrial Combination Spanners – AF
AF
Manufactured from chrome vanadium steel with a satin finish body and highly polished heads. 15 open jaw angle to shank and ring end offset.
Conform to:
5.5mm – 25mm, 1/4″ – 1″ AF – DIN 3113.
26mm – 50mm, 11/16″ – 2″AF – ASME B107.6.
1/8″ – 1/2″ Whitworth – DIN 3113 & BS192:1982.
9/16″ – 7/8″ Whitworth – ASME B107.6 & BS192:1982. -
2″ A/F DEEP IMPACT SKT 1″ SQ DRRead moreKennedy Chrome Molybdenum Impact Sockets: 1″ Drive Inch Size, Deep Length, 6-Point
1â Drive Inch Size, Deep Length, 6-Point
Conform to: SAE, USA Federal Standard GGG-W-660A.Manufactured from high quality chrome molybdenum steel. Black oxidised finish with permanent laser etched markings.