Archives: Products
Showing 4273–4288 of 23773 results
-
14.00mm HSS S/S L/S DRILLRp333.000Read moreHSS Straight Shank Long Series Drills – Steam Tempered
General purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, web thickness: normal, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of f11. Manufactured to BS 328; Part 1: 1986, DIN 340 RN, ISO 494.
-
14.00mm HSS S/S SP/FL MACHINE REAMERRp1.244.000Read moreStraight Shank Machine Reamers
Left hand spiral flute, right hand cutting. Manufactured to BS 328-4.
Metric Tolerances (to H7)
Diameter: ~ up to 3.00. Tolerance: High +0.008, Low -0.004.
Diameter: Over 3.00 ~ up to 6.00. Tolerance: High +0.010, Low -0.005.
Diameter: Over 6.00 ~ up to 10.00. Tolerance: High +0.012, Low -0.006.
Diameter: Over 10.00 ~ up to 18.00. Tolerance: High +0.015, Low -0.008. -
14.00mm HSS S/S ST/FL HAND TAPER PIN REAMERRead moreHSS Straight Shank Hand Taper Pin Reamers
Used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies. Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.
Metric Tolerances
Diameter: Over 1.50 ~ up to 5.00. Tolerance: +0.075, -0.000.
Diameter: Over 5.00 ~ up to 20.00. Tolerance: +0.125, -0.000. -
14.00mm HSS S/S STUB DRILLRp170.000Read moreSherwood HSS General Purpose Stub Drills – Metric Sizes
Series S100 – Metric
General purpose drills for use on automatics and turret lathes. Suitable for drilling steels, cast iron, alloy steel and malleable cast iron. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BSâ328: Part 1: 1986/DIN 1897. -
14.00mm HSS SP/FL PARALLEL HAND REAMERRp805.000Read moreStraight Shank Parallel Hand Reamers
Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.
Metric Tolerances
Diameter: ~ up to 3.00. Tolerance: +0.008, -0.007.
Diameter: Over 3.00 ~ up to 6.00. Tolerance: +0.010, -0.005.
Diameter: Over 6.00 ~ up to 10.00. Tolerance: +0.012, -0.006.
Diameter: Over 10.00 ~ up to 18.00. Tolerance: +0.015, -0.008.
Diameter: Over 18.00 ~ up to 30.00. Tolerance: +0.017, -0.009.
Diameter: Over 30.00 ~ up to 50.00. Tolerance: +0.021, -0.012. -
14.00mm HSS T/S DRILLRp303.000Read moreHSS Taper Shank Drills, 1 Morse Taper – Metric
To drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8.
Manufacturing Standard: DIN 345. -
14.00mm HSS T/S SP/FL MACHINE REAMERRp836.000Read moreTaper Shank Machine Reamers
Used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head. Manufactured to BS 328-4.
Tolerances (to H7)
Diameter: ~ up to 3.00. Tolerance: +0.008, -0.007.
Diameter: Over 3.00 ~ up to 6.00. Tolerance: +0.010, -0.005.
Diameter: Over 6.00 ~ up to 10.00. Tolerance: +0.012, -0.006.
Diameter: Over 10.00 ~ up to 18.00. Tolerance: +0.015, -0.008.
Diameter: Over 18.00 ~ up to 30.00. Tolerance: +0.017, -0.009.
Diameter: Over 30.00 ~ up to 50.00. Tolerance: +0.021, -0.012.
Diameter: Over 50.00 ~ up to 80.00. Tolerance: +0.025, -0.014.
Diameter: Over 80.00 ~ up to 120.00. Tolerance: +0.029, -0.016. -
14.00mm HSS-COBALT S/S SP/FL CHUCKING REAMERRp1.421.000Read moreCobalt Straight Shank Chucking Reamers
Manufactured to DIN 212.
Tolerances (to H7)
Diameter: ~ up to 5.50. Tolerance: +0.004, -0.000.
Diameter: Over 5.50 ~. Tolerance: +0.005, -0.000. -
14.00mm HSS-COBALT T/S DRILLRp572.000Read moreHSS-Co 5% Taper Shank Drills
High heat resistant drill for drilling alloyed and unalloyed steels and castings with a tensile strength over 800N/mm2. Especially suitable for hot and cold rolled steels as well as case hardening and heat treatable steels. Manufactured to Type N DIN 345.345.
-
14.00mm Q-COAT CARBIDE DRILL 3xDRead moreSolid Carbide Q-Coat Drill
For drilling into general steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous heavy and light metal, and abrasive plastic, self-centering.
Point angle: 140°, tolerance of diameter: m7, tolerance of shank: h6. Manufactured to DIN 6537. -
14.00mm Q-COAT CARBIDE DRILL 5xDRead moreSolid Carbide Q-Coat Drill
For drilling into general steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous heavy and light metal, and abrasive plastic, self-centering.
Point angle: 140°, tolerance of diameter: m7, tolerance of shank: h6. Manufactured to DIN 6537. -
14.00mm Q-COAT COOLANT CARBIDE DRILL 5xDRead moreSolid Carbide Q-Coat Drill
For drilling into general steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous heavy and light metal, and abrasive plastic, self-centering.
Point angle: 140°, tolerance of diameter: m7, tolerance of shank: h6. Manufactured to DIN 6537. -
14.00mm x 250mm O/A HSS TAPER SHANK DRILLRead moreHSS Extra Length Taper Shank Drills to BS328 : 1 1986 – 1 Morse Taper, Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite. Point angle 118°, helix angle: normal, web thickness: standard, relief angle 8° – 20°, tolerance of diameter: h8. Made to BS328 : 1 1986. Sizes 32mm to 50mm are made to DIN1870/Series 1.
-
14.00mm x 315mm O/A HSS S/S DRILLRp700.000Read moreHSS Extra Length Drills – Steam Tempered
General-purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328 : Part 1 : 1986.
-
14.00mm x 315mm O/A HSS TAPER SHANK DRILLRead more
HSS Extra Length Taper Shank Drills to BS328 : 1 1986 – 1 Morse Taper, Metric
General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite. Point angle 118°, helix angle: normal, web thickness: standard, relief angle 8° – 20°, tolerance of diameter: h8. Made to BS328 : 1 1986. Sizes 32mm to 50mm are made to DIN1870/Series 1.
-
14.00mm x 400mm O/A HSS S/S DRILLRp1.007.000Add to cart
HSS Extra Length Drills – Steam Tempered
General-purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118°, helix angle: normal, web thickness: standard, relief angle: 10° – 20°, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328 : Part 1 : 1986.